Please type complete and accurate the model ID specified by manufacturer. No Serial numbers please. Examples: 1998 American Standard / 2011 Strat Deluxe / Les Paul copy / etc.
Right Handed
0.00 USD
Left Handed
8.50 USD
Combinations that work well
AVn-60n Gen-2 / AVn-60b
AVn-48n Gen-2 / AVn-48b
Impersonator 52n / Impersonator 52b and Twang-Blaster
Neck Blaster / Bridge Blaster
Twang-Blaster neck / Twang-Blaster bridge
Combinations that don't work well***
AVn-60n Gen-2 with AVn-48b, Impersonator 52b, Bridge Blaster and Twang-Blaster
AVn-48n Gen-2 with AVn-60b, Impersonator 52b, Bridge Blaster and Twang-Blaster
Cover Options
Gold Plated
Non-Plated
Cover Options
Gold plated
Hand Buffed Nickel-Silver
Get the most out of your new pickups by providing them with optimum electrical environment so they achieve their full sonic potential with our Goodbye-Soldering Harness (DIY Plug-n-Play install kit) where pickups & higher quality controls & wiring are installed fast and easy without any soldering.
Please go to the TAB below and choose your Harness model.
Choose For Soldering into your guitar if the pickups are to be connected to stock guitar electrics other than a Kinman Goodbye Soldering Harness that uses miniature plugs.
Cables are long enough for Stock guitars. If you require longer cables send a follow-up 'CONTACT' message stating the length of cables you require.
Cable length of our Telecaster Pickups are:
- neck 320mm
- middle 265mm
- bridge 310mm
Choose Plug into a Kinman Harness if the pickups are to be used with an existing Kinman Goodbye Soldering Harness
Note: Older versions of Kinman Harness use solder connections, please check
Cables are long enough for Stock guitars. If you require longer cables send a follow-up 'CONTACT' message stating the length of cables you require.
- neck 320mm
- middle 265mm
- bridge 310mm
Choose For Soldering into your guitar if the pickups are to be connected to stock guitar electrics other than a Kinman Goodbye Soldering Harness that uses miniature plugs.
if in doubt choose the first option since it suits either shielding condition
3 conductor hook-up cable plus grounded magnets are necessary for Series switching and/or Phase reversing. (in a set of 3 in a Kinman K9 harness, it's for middle pickup only) +$15 upcharge.
Cables are long enough for Stock Strats. If you require longer cables state the lengths you require in the ADDITIONAL NOTES box on the Shipping page. Lengths stated below are from the middle of the pickup to the tip of the cable.
neck 250mm (9-3/4") long
middle 188mm (7-3/8") long
bridge 152mm (6") long
Choose For Soldering into your guitar if the pickups are to be connected to stock guitar electrics other than a Kinman Goodbye Soldering Harness that uses miniature plugs.
3 conductor hook-up cable is necessary for Series switching and/or Phase reversing.
This kit is positive latching and will not come apart without force. It has short leads and is intended to connect a normal pickup hook-up cable to the original pickup cable after the original pickup has been cut from it. Details are in >Technical >Install Guides.
Choose For Soldering into your guitar if the pickups are to be connected to stock guitar electrics other than a Kinman Goodbye Soldering Harness that uses miniature plugs.
3 conductor hook-up cable plus grounded magnets are necessary for Series switching and/or Phase reversing. (in a set of 3 it's for middle pickup only) +$15 upcharge.
The ground is a separate wire from the Plug and is not shown.
Cables are long enough for Stock Strats. If you require longer cables state the lengths you require in the ADDITIONAL NOTES box on the Shipping page. Lengths stated below are from the middle of the pickup to the tip of the cable.
neck 250mm (9-3/4") long
middle 188mm (7-3/8") long
bridge 152mm (6") long
Please indicate what the Bridge pickup is: Humbucker* or P-90 it will have 500k Volume pot load Strat pickups will have 250k Ohm Volume pot load.
NOTE: * Humbuckers can not be split to single coil with this harness.
Choose the K9-H instead.
Please indicate what the Bridge pickup are: Humbucker* or P-90 it will have 500k Volume pot load Strat pickups will have 250k Ohm Volume pot load.
NOTE: * Humbuckers can not be split to single coil with this harness.
Choose the K9-H instead.
Strat pickups require 250k volume pot load.
Which positions are for Humbucker or P-90 that require 500k volume pot load.
Is the harness for a rear rout install where the controls are mounted through the wood? Click to see image.
Synergy is an interaction or cooperation giving rise to a whole that is greater than the simple sum of its parts. The term synergy comes from the Attic Greek word συνεργία synergia meaning working together.
An opus is a created work, usually musical in nature.
A common usage of opus is with the term magnum opus which refers to one's greatest work, musical or otherwise
https://www.vocabulary.com/dictionary/opus
this_content
